How to arrange Taguchi response data in the worksheet

In a usual Taguchi robust parameter design experiment, you would subject each control factor combination to each of the noise conditions and measure the response variable. If you are doing a dynamic experiment, the response is measured at each level of the signal factor. Record the results for each noise condition in a separate response column in the worksheet.

Columns A–E (the control factors) and Pressure (the signal factor) are columns of the orthogonal array design. Noise1 and Noise2 are the response data that were measured at each noise condition.

A	B	C	D	E	Pressure	Noise1	Noise2
1	1	1	1	1	20	37	48
1	1	1	1	1	40	71	93
1	1	2	2	2	20	29	44
1	1	2	2	2	40	51	86
2	2	1	1	2	20	19	30
2	2	1	1	2	40	39	57
2	2	2	2	1	20	33	39
2	2	2	2	1	40	62	76
1	2	1	2	1	20	25	33
1	2	1	2	1	40	51	60
1	2	2	1	2	20	44	60
1	2	2	1	2	40	79	109
2	1	1	2	2	20	31	44
2	1	1	2	2	40	66	82
2	1	2	1	1	20	22	32
2	1	2	1	1	40	47	65

Minitab.com
License Portal
Store
Blog
Contact Us
Cookie Settings

A	B	C	D	E	Pressure	Noise1	Noise2
1	1	1	1	1	20	37	48
1	1	1	1	1	40	71	93
1	1	2	2	2	20	29	44
1	1	2	2	2	40	51	86
2	2	1	1	2	20	19	30
2	2	1	1	2	40	39	57
2	2	2	2	1	20	33	39
2	2	2	2	1	40	62	76
1	2	1	2	1	20	25	33
1	2	1	2	1	40	51	60
1	2	2	1	2	20	44	60
1	2	2	1	2	40	79	109
2	1	1	2	2	20	31	44
2	1	1	2	2	40	66	82
2	1	2	1	1	20	22	32
2	1	2	1	1	40	47	65

A	B	C	D	E	Pressure	Noise1	Noise2
1	1	1	1	1	20	37	48
1	1	1	1	1	40	71	93
1	1	2	2	2	20	29	44
1	1	2	2	2	40	51	86
2	2	1	1	2	20	19	30
2	2	1	1	2	40	39	57
2	2	2	2	1	20	33	39
2	2	2	2	1	40	62	76
1	2	1	2	1	20	25	33
1	2	1	2	1	40	51	60
1	2	2	1	2	20	44	60
1	2	2	1	2	40	79	109
2	1	1	2	2	20	31	44
2	1	1	2	2	40	66	82
2	1	2	1	1	20	22	32
2	1	2	1	1	40	47	65

A	B	C	D	E	Pressure	Noise1	Noise2
1	1	1	1	1	20	37	48
1	1	1	1	1	40	71	93
1	1	2	2	2	20	29	44
1	1	2	2	2	40	51	86
2	2	1	1	2	20	19	30
2	2	1	1	2	40	39	57
2	2	2	2	1	20	33	39
2	2	2	2	1	40	62	76
1	2	1	2	1	20	25	33
1	2	1	2	1	40	51	60
1	2	2	1	2	20	44	60
1	2	2	1	2	40	79	109
2	1	1	2	2	20	31	44
2	1	1	2	2	40	66	82
2	1	2	1	1	20	22	32
2	1	2	1	1	40	47	65