Run
Tune
Hyperparameters to Identify a Better Model
button after the Model Summary table.
.
Click the

Run Tune Hyperparameters to Identify a Better Model button after the Model Summary table. . Click the

This command is available with the Predictive Analytics Module. Click here for more information about how to activate the module.

The performance of TreeNet^{®} models is generally sensitive to
values of the learning rate, the subsample fraction, and the complexity of the
individual trees that form the model. In the results for a model, click
Tune
Hyperparameters to Identify a Better Model
to evaluate multiple values of these hyperparameters to learn which combination
produces the best values of an accuracy criterion, such as the average
–loglikelihood. Better values of these hyperparameters have the potential to
significantly improve prediction accuracy, so the exploration of different
values is a common step in the analysis.

You can also adjust the number of trees that the model includes. In general, 300 trees is enough to distinguish values of the hyperparameters. Generally, you increase the number of trees when the optimal number of trees for one or more models of interest is close to the maximum number of trees. If the number of trees is closer to the maximum number, an increase in the number of trees is more likely to improve the performance of the model.

Specify one or more values for each hyperparameter to evaluate. The analysis evaluates the hyperparameters to find the combination with the best value of the accuracy criterion. If you enter no values for a hyperparameter, the evaluation uses the value for that hyperparameter from the model in the results. If the response is binary and the original model specifies the proportion of events and nonevents to sample, the evaluation always uses the proportions from the original model.

Enter up to 10 values. Eligible values are from 0.0001 to 1.

Enter up to 10 values. Eligible values are greater than 0 and less than or equal to 1.

Subsample fraction is disabled when the original model specifies the proportion of events and nonevents to sample for a binary response.

Choose whether to evaluate the
Maximum
terminal nodes
or the
Maximum tree
depth.
Usually, either choice is a reasonable way to identify a useful model and the
selection depends only on individual preference.

- Maximum terminal nodes
- Enter up to 3 values. Eligible values are between 2 and 2000. Usually, the default value of 6 provides a good balance between calculation speed and the investigation of interactions among variables. A value of 2 eliminates the investigation of interactions.
- Maximum tree depth
- Enter up to 3 values. Eligible values are between 2 and 1000 to represent the maximum depth of a tree. The root node corresponds to a depth of 1. In many applications, depths from 4 to 6 give reasonably good models

Enter a value between 1 and 5000 to specify the maximum number of trees to build. The default value of 300 usually provides useful results for the evaluation of the hyperparameter values.

If one or more models of interest have a number of trees that is close to the number of trees that you specify, then consider whether to increase the number of trees. If the number of trees is closer to the maximum number, an increase in the number of trees is more likely to improve the performance of the model.

If you specify values for more than one hyperparameter, then the models in
the evaluation table depend on whether you evaluate the complete combinations
of the hyperparameters.

- If you select Evaluate complete parameter combinations, then the algorithm evaluates every combination of the hyperparameters. This option generally takes longer to calculate.
- Otherwise, the algorithm
evaluates the hyperparameters in this order:
- Learning rate
- Subsample fraction
- Individual tree complexity parameter

For example, suppose that the algorithm receives the following hyperparameters:- Learning rates: 0.001, 0.01, 0.1
- Subsample fractions: 0.4, 0.5, 0.7
- Maximum numbers of terminal nodes: 4, 6

- The algorithm sets the subsample proportion to 0.4 and the maximum number of terminal nodes to 4. Then, the algorithm evaluates the learning rates in order from least to greatest: 0.001, 0.01, 0.1.
- Suppose the algorithm identifies 0.01 as the best learning rate. Then the algorithm sets the learning rate to 0.01 and the maximum number of terminal nodes to 4. Then, the algorithm evaluates the subsample proportions of 0.4, 0.5, and 0.7.
- Suppose that the algorithm identifies 0.5 as the best subsample proportion. Then the algorithm sets the learning rate to 0.01, the subsample proportion to 0.5. Then, the algorithm evaluates the maximum numbers of nodes of 4 and 6.
- Suppose that the algorithm identifies 6 as the best maximum number of terminal nodes. Then Minitab produces the evaluation table and the results for the model with learning rate = 0.01, subsample proportion 0.5, and maximum number of terminal nodes 6.

In this example, the analysis that does not evaluate the complete set of parameter combinations includes 8 models in the evaluation table. An analysis of all the parameter combinations has 3 × 3 × 2 = 18 combinations and takes longer to calculate.

After you specify the values to examine, click Display Results. In a new set of results, Minitab produces a table that compares the accuracy criterion for the hyperparameter combinations and the results for the model with the best value of the accuracy criterion.

Minitab recreates the same tables and graphs for the new model as for the original model. The tables and graphs for the new model are in a new set of results. Storage is the same as for the original analysis. The storage columns are in the same worksheet. For example, if the original analysis stored the fitted values in a column titled "Fit," then the new analysis titles an empty column "Fit_1" and stores the fitted values.