A factorial design is type of designed experiment that lets you study of the effects that several factors can have on a response. When conducting an experiment, varying the levels of all factors at the same time instead of one at a time lets you study the interactions between the factors.

In the following plots, each point represents a unique combination of factor levels.

You can either run the full factorial design or a fraction of the factorial design.

When you have a factorial design with center points you can test whether there is curvature in the response surface. However, you cannot model the effect of that curvature anywhere but at the center point. In other words, you can only calculate the fitted values at the corner points and the center point of the design, and thus cannot create a contour plot. You need to have quadratic terms (for example, square terms) in the model in order to model the curvature across the whole response surface. This is possible with a response surface design. You can augment the factorial design with axial points to create a central composite response surface design from a factorial design.

A full factorial design is a design in which researchers measure responses at all combinations of the factor levels. Minitab offers two types of full factorial designs:

- 2-level full factorial designs that contain only 2-level factors.
- general full factorial designs that contain factors with more than two levels.

The number of runs necessary for a 2-level full factorial design is 2^{k} where k is the number of factors. As the number of factors in a 2-level factorial design increases, the number of runs necessary to do a full factorial design increases quickly. For example, a 2-level full factorial design with 6 factors requires 64 runs; a design with 9 factors requires 512 runs. A half-fraction, fractional factorial design would require only half of those runs.

A fractional design is a design in which experimenters conduct only a selected subset or "fraction" of the runs in the full factorial design. Fractional factorial designs are a good choice when resources are limited or the number of factors in the design is large because they use fewer runs than the full factorial designs.

A fractional factorial design uses a subset of a full factorial design, so some of the main effects and 2-way interactions are confounded and cannot be separated from the effects of other higher-order interactions. Usually experimenters are willing to assume the higher-order effects are negligible in order to achieve information about main effects and low-order interactions with fewer runs.

In a 2-level full factorial design, each experimental factor has only two levels. The experimental runs include all combinations of these factor levels. Although 2-level factorial designs are unable to explore fully a wide region in the factor space, they provide useful information for relatively few runs per factor. Because 2-level factorial designs can identify major trends, you can use them to provide direction for additional experimentation. For example, when you need to explore a region where you believe optimal settings may exist, you can augment a factorial design to form a central composite design.

The following diagrams show a full factorial design versus a ½ fractional factorial design.

The full factorial design contains twice as many design points as the ½ fraction design. The response is only measured at four of the possible eight corner points of the factorial portion of the design. However, with this design, the main effects will be confounded with the 2-way interactions.

The fractions of a design are ordered based on the signs assigned to the design generators. For example, consider a 6 factor, 8 run design. The design generators are D = AB, E = AC, F = BC. This a 1/8 fraction of a full 6 factor design. Thus there are 8 fractions. These are ordered as follows:

Fraction | Standard (Yates) Order | Design Generator |
---|---|---|

1 | – – – | D = –AB, E = –AC, F = –BC |

2 | + – – | D = +AB, E = –AC, F = –BC |

3 | – + – | D = –AB, E = +AC, F = –BC |

4 | + + – | D = +AB, E = +AC, F = –BC |

5 | – – + | D = –AB, E = –AC, F = +BC |

6 | + – + | D = +AB, E = –AC, F = +BC |

7 | – + + | D = –AB, E = +AC, F = +BC |

8 | + + + | D = +AB, E = +AC, F = +BC |

The principal fraction is always the last one, the one that has all + signs.

Suppose we create the second fraction. We start with the 3 factor full factorial then add the factors D = AB, E = -AC, F = -BC, giving:

Run | A | B | C | D = AB | E = –AC | F = –BC |
---|---|---|---|---|---|---|

1 | – | – | – | + | – | – |

2 | + | – | – | – | + | – |

3 | – | + | – | – | – | + |

4 | + | + | – | + | + | + |

5 | – | – | + | + | + | + |

6 | + | – | + | – | – | + |

7 | – | + | + | – | + | – |

8 | + | + | + | + | – | – |

When you create a fractional factorial design, Minitab uses the principal fraction by default. The principal fraction is the fraction where all signs are positive. However, there may be situations when a design contains points that are impractical to conduct and choosing an appropriate fraction can avoid these points.

A full factorial design with 5 factors requires 32 runs. If you want only 8 runs, you need to use a one-fourth fraction. You can use any of the four possible fractions of the design. Minitab numbers the runs in standard order (also called Yates' order) order using the design generators as follows:

- D = –AB E = –AC
- D = AB E = –AC
- D = –AB E = AC
- D = AB E = AC

For example, suppose you could not conduct your design with all five factors set at their high level. The principal fraction contains this point, but the third fraction does not.