Find definitions and interpretation guidance for every statistic and graph that is provided with single exponential smoothing.

The smoothing constant (also known as α) is the weight used in the level component of the smoothed estimate. α is similar to a moving average of the observations. The weights adjust the amount of smoothing by defining how each component reacts to current conditions. Lower weights give less weight to recent data, which produces a smoother line. Higher weights give more weight to recent data, which produces a less smooth line.

The mean absolute percent error (MAPE) expresses accuracy as a percentage of the error. Because the MAPE is a percentage, it can be easier to understand than the other accuracy measure statistics. For example, if the MAPE is 5, on average, the forecast is off by 5%.

However, sometimes you may see a very large value of MAPE even though the model appears to fit the data well. Examine the plot to see if any data values are close to 0. Because MAPE divides the absolute error by the actual data, values close to 0 can greatly inflate the MAPE.

Use to compare the fits of different time series models. Smaller values indicate a better fit. If a single model does not have the lowest values for all 3 accuracy measures, MAPE is usually the preferred measurement.

The accuracy measures are based on one-period-ahead residuals. At each point in time, the model is used to predict the Y value for the next period in time. The difference between the predicted values (fits) and the actual Y are the one-period-ahead residuals. Because of this, the accuracy measures provide an indication of the accuracy you might expect when you forecast out 1 period from the end of the data. Therefore, they do not indicate the accuracy of forecasting out more than 1 period. If you're using the model for forecasting, you shouldn't base your decision solely on accuracy measures. You should also examine the fit of the model to ensure that the forecasts and the model follow the data closely, especially at the end of the series.

The mean absolute deviation (MAD) expresses accuracy in the same units as the data, which helps conceptualize the amount of error. Outliers have less of an effect on MAD than on MSD.

Use to compare the fits of different time series models. Smaller values indicate a better fit.

The accuracy measures are based on one-period-ahead residuals. At each point in time, the model is used to predict the Y value for the next period in time. The difference between the predicted values (fits) and the actual Y are the one-period-ahead residuals. Because of this, the accuracy measures provide an indication of the accuracy you might expect when you forecast out 1 period from the end of the data. Therefore, they do not indicate the accuracy of forecasting out more than 1 period. If you're using the model for forecasting, you shouldn't base your decision solely on accuracy measures. You should also examine the fit of the model to ensure that the forecasts and the model follow the data closely, especially at the end of the series.

The mean square deviation (MSD) measures the accuracy of the fitted time series values. Outliers have a greater effect on MSD than on MAD.

Use to compare the fits of different time series models. Smaller values indicate a better fit.

The accuracy measures are based on one-period-ahead residuals. At each point in time, the model is used to predict the Y value for the next period in time. The difference between the predicted values (fits) and the actual Y are the one-period-ahead residuals. Because of this, the accuracy measures provide an indication of the accuracy you might expect when you forecast out 1 period from the end of the data. Therefore, they do not indicate the accuracy of forecasting out more than 1 period. If you're using the model for forecasting, you shouldn't base your decision solely on accuracy measures. You should also examine the fit of the model to ensure that the forecasts and the model follow the data closely, especially at the end of the series.

The forecasts are the fitted values obtained from the time series model. Minitab displays the number of forecasts that you specify. The forecasts begin either at the end of the data or at the point of origin that you specify.

Use forecasts to predict a variable for a specified period of time. For example, a warehouse manager can model how much product to order for the next 3 months based on the previous 60 months of orders.

Examine the fits and the forecasts in the plot to determine whether the forecasts are likely to be accurate. The forecasts should follow the general flow of the data at the end of the series. Because the forecasts from single exponential smoothing are constant, it is important that there is no trend in the data before the forecasts. If there is a trend before the forecasts, the forecasts may not be accurate.

The forecasts from single exponential smoothing are very conservative because they are based solely on the latest estimate of the level, and no estimate of the trend. You should usually only forecast 6 periods into the future.

The lower and upper prediction limits produce a prediction interval for each forecast. The prediction interval is a range of likely values of forecasts. For example, with a 95% prediction interval, you can be 95% confident that the prediction interval contains the forecast at the specified time.

The smoothing plot displays the observations versus time. The plot includes the fits that are calculated from the smoothing procedure, the forecasts, the smoothing constant, and the accuracy measures. You can also choose to display the smoothed values instead of the fits.

Examine the smoothing plot to determine whether your model fits your data. If the fits closely follow the actual data, the model fits your data.

- If the model fits the data, you can perform moving average and compare the two models.
- If the model does not fit the data, examine the plot for trends or seasonality. If you see evidence of these, you should use a different time series analysis. For more information, go to Which time series analysis should I use?.

The normal plot of the residuals displays the residuals versus their expected values when the distribution is normal.

Use the normal plot of the residuals to determine whether the residuals are normally distributed. However, this analysis does not require normally distributed residuals.

If the residuals are normally distributed, the normal probability plot of the residuals should approximately follow a straight line. The following patterns imply that the residuals are not normally distributed.

The residuals versus fits plot displays the residuals on the y-axis and the fitted values on the x-axis.

Use the residuals versus fits plot to determine whether the residuals are unbiased and have a constant variance. Ideally, the points should fall randomly on both sides of 0, with no recognizable patterns in the points.

The patterns in the following table may indicate that the residuals are biased and have a nonconstant variance.

Pattern | What the pattern may indicate |
---|---|

Fanning or uneven spreading of residuals across fitted values | Nonconstant variance |

Curvilinear | A missing higher-order term |

A point that is far away from zero | An outlier |

If you see nonconstant variance or patterns in the residuals, your forecasts may not be accurate.

The histogram of the residuals shows the distribution of the residuals for all observations. lf the model fits the data well, the residuals should be random with a mean of 0. So the histogram should be approximately symmetric around 0.

The residuals versus order plot displays the residuals in the order that the data were collected.

Use the residuals versus order plot to determine how accurate the fits are compared to the observed values during the observation period. Patterns in the points may indicate that model does not fit the data. Ideally, the residuals on the plot should fall randomly around the center line.

The following patterns may indicate that the model does not fit the data.

Pattern | What the pattern may indicate |
---|---|

A consistent long-term trend | The model does not fit the data |

A short-term trend | A shift or a change in pattern |

A point that is far away from the other points | An outlier |

A sudden shift in the points | The underlying pattern for the data has changed |

The following examples show patterns that may indicate that the model does not fit the data.

The residuals versus variables plot displays the residuals versus another variable.

Use the plot to determine whether the variable affects the response in a systematic way. If patterns are present in the residuals, the other variables are associated with the response. You can use this information as the basis for additional studies.